We need to remove embroidery for many reasons. Sometimes it may be embroidery mistakes, sometimes it may not be as expected or anything. When you need to remove any embroidery, it is more convenient to use a seam ripper than anything else.
However, you might not always have access to a seam ripper, which will create a problem. And that’s why you need to learn how to remove embroidery without a seam ripper for your convenience.
It is also possible to redo embroidery over the previous one. This easy-to-read article contains a detailed discussion that will help you remove embroidery without a seam ripper.
Can You Remove Embroidery from a Hat?
Hats have thicker embroidery thread or logo stitches than general clothing. Using a trimmer will be easy for that. However, you can do that with embroidery scissors or blades too. You need to drive the sharp blades carefully a couple of times on the thick layers of stitches. Read the ‘finishing’ step in the middle of this article to wrap up the job!
Nowadays embroidery machines have built-in reverse stitching features. That also helps to embroider anything easily. Sometimes only the bobbin thread makes it a bit difficult.
Be it hats or regular clothing, and you can follow three simple steps while taking out the unwanted embroidery. Before that, let’s see what tool can replace a seam ripper.
Replacing a Seam Ripper
Using a seam ripper is the easiest way for professionals. Scissors or Blades are also acceptable. We have a list that can replace seam rippers while removing any embroidery.
Now, sometimes trimmers work better instead of stitch erasers. But the blades of the trimmer need to be close enough for this. Otherwise, we would recommend you not to use the trimmer. If you own a stitch eraser, you are in luck! You can easily loosen the stitches with it.
While using scissors, you should pick a relatively small pair. Most of the embroidery stitches are wafer-thin, and the fabric is, of course, susceptible. So, it is wise to choose a smaller set of scissors.
You may use sharp pins for this job. You can only use them if they are strong enough to trim the thread. Otherwise, we wouldn’t recommend those.
Read Article: Best Embroidery Machine
What is the Easiest Way to Remove Embroidery?
There is a common question, should we iron the cloth or use a hairdryer before removing the embroidery? There are different type of embroidery and there is no advantage of ironing before removing the embroidery.
Let’s get started with our three easy steps to remove any piece of embroidery.
Hold the piece of fabric steadily on a flat surface. It is wise to start from the inside part of the garment. That way, there will not be any vivid marks.
In general, you should start from one end of the embroidery to another. But if the embroidery is a ‘serged seam,’ there is an easier way for that. We will learn about it in the latter part of the article.
2. Removing the Embroidery
Razor Blade/ Eyebrow razor/ Scissors: Draw the blade parallel to the stitched plane line. You shouldn’t pick up more than three threads each time. Remember that patience is the only key here. Cutting the middle stripe is the hardest part of the whole job.
After a couple of runs of the blade, you will find that the threads have started to loosen up. Use your fingers or a tweezer to pick/pull up the remaining lines.
Stitch Eraser/Trimmer: Hold the trimmer parallel to the stitched plane line. Gently run it a couple of times on the plane line. The stitch will loosen up, and the threads will be easier to pull out. Just like before, you can use your fingers or a tweezer.
A stitch eraser or trimmer comes in handy if the embroidery stitch is thick. Otherwise, use the blade or scissors.
Serged Seam: A serged embroidery process is easier to remove. You can use a pair of scissors or blades instead of using a seam ripper.
You don’t need to hold at one end of the stitch. Just select a random loop in the middle.
- Slip the blade of the scissors in the loop. Run the knife back and forth a couple of times, and what will cut the thread by then. Pay special attention to the end of the blade so that you don’t damage the fabric.
- Leave 4/5 loops, and select another loop and go all over again.
- Pick up any thread in between the loops and pull it. You will see that the embroidery stitching stitches are open now, and the lines are coming out very quickly.
While using the blade, hold it steadily and run it back and forth a couple of times. The thread will loosen up, and eventually, what will remove them. Again, focus on the end of the blade and make sure not to damage the fabric.
Double-thread stitches in machine embroidery, draw the blade back and forth to cut them both and select a nearby loop. Same as earlier, pull the thread in between.
Use your fingers or a tweezer for picking up raw threads around the area. You may also use a piece of ‘tape’ to do it. Apply the tape and remove it out a couple of times, and you will have the raw threads removed.
You can wash the hat or the cloth after you are finished. You can also iron it if you want.
Can Embroidery Be Removed and Redone?
The answer is- Yes! You can remove the embroidery and redo it as you want. But, you have to be quite careful to do that. When you have removed the embroidery,
there may be some stitch hole-marks left in the garment. If they are vivid, you can select a good-looking logo or do another embroidery to wrap that up. That is the smartest thing to do if the left holes are too vivid.
If you have redone the embroidery, do not iron the front side. It may damage the design or the structure.
Read Article: How To Choose The Best Embroidery Machine
Bottom Line: How to Remove Embroidery Without a Seam Ripper
Removing embroidery or logo from a piece of cloth is an essential tailoring function. While it might seem complicated, we hope you have found the most straightforward answer to the question- how to remove embroidery without a seam ripper.
Last note, pay attention to the type of fabric that will not be damaged after re-stitching the embroidery.